黄春林,朱明,鲁金涛,黄锦阳,党莹樱,袁勇

• 1:西安热工研究院有限公司清洁低碳热力发电系统集成及运维国家工程研究中心
• 2:西安科技大学材料科学与工程学院

摘要(Abstract)：

在高温下长时间暴露，钢材表面的铝化物涂层与母材间容易发生元素互扩散，对母材组织产生影响，进而影响母材的力学性能。为研究超超临界机组用T92钢表面铝化物涂层的高温强度特性，采用低温粉末包埋渗铝法在T92钢锅炉管内壁制备铝化物涂层，并在室温至625℃环境中进行拉伸试验以及在625℃环境中进行持久试验，结合扫描电镜（SEM）、金相显微镜（OM）观察及X射线衍射分析，研究铝化物涂层对T92钢基体拉伸性能与持久寿命影响行为。研究结果表明：低温粉末包埋渗铝可在T92锅炉管内壁制备厚度约30.4μm的双层结构铝化物涂层，各层结构连续均匀且组织稳定，与母材呈冶金结合；在室温至625℃拉伸过程中，涂层为柱状晶结构且表面发生皴裂；625℃长时持久蠕变过程中，Fe-Al涂层裂纹数量分布多，但裂纹深度浅，极少数裂纹向基体扩展；高应力状态下大应变导致涂层发生局部剥落。铝化物涂层经长时间蠕变形变，仍与T92钢基体呈良好的冶金结合。

关键词(KeyWords)： 铝化物涂层;T92钢;高温拉伸;高温持久;锅炉管

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金项目（52271070）;; 中国华能集团有限公司总部科技项目（HNKJ20-H41）~~

作者(Author): 黄春林,朱明,鲁金涛,黄锦阳,党莹樱,袁勇

DOI: 10.19666/j.rlfd.202212202

参考文献(References)：

• [1]王伟,唐丽英,李文胜,等. T92钢内压蠕变试验组织性能老化规律[J].热力发电, 2016, 45(9):1-6.WANG Wei, TANG Liying, LI Wensheng, et al.Microstructure and properties evolution of T92 steel used for boiler tube during internal pressure creep test[J].Thermal Power Generation, 2016, 45(9):1-6.
• [2] SHIGETA J I, HAMAO Y, AOKI H, et al. Development of a coal ash corrosivity index for high temperature corrosion[J]. Journal of Engineering Materials and Technology, 1987, 109(4):299-305.
• [3]王静静,周云龙.过热器再热器爆漏事故的原因分析及对策[J].应用能源技术, 2010(6):33-36.WANG Jingjing, ZHOU Yunlong. Cause and analysis on superheater and reheater tube explosion and its countermeasures[J]. Applied Energy Technology,2010(6):33-36.
• [4] ABE F, HORIUCHI T, TANEIKE M, et al. Stabilization of martensitic microstructure in advanced 9Cr steel during creep at high temperature[J]. Materials Science and Engineering A, 2004, 378(1/2):299-303.
• [5]王学,于淑敏,任瑶瑶,等. P92钢时效的Laves相演化行为[J].金属学报, 2014, 50(10):1195-1202.WANG Xue, YU Shumin, REN Yaoyao, et al. Laves phase evolution in P92 steel during ageing[J]. Acta Metallurgica Sinica, 2014, 50(10):1195-1202.
• [6] CHANDRA K, KRANZMANN A, SALIWAN NEUMANN R, et al. High temperature oxidation behavior of 9–12%Cr ferritic/martensitic steels in a simulated dry oxyfuel environment[J]. Oxidation of Metals, 2014, 83(3/4):291-316.
• [7]党莹樱,鲁金涛,黄锦阳,等. AlSi涂覆的TP347H FG高温持久行为[C]//中国电机工程学会.中国电机工程学会年会论文集:2019年卷.武汉:国网电力科学研究院, 2019:224-228.DANG Yingying, LU Jintao, HUANG Jinyang, et al. High temperature creep rupture behavior of slurry Al-Sicoating on TP347H FG[C]//Chinese Society Electrical Engineering. Annual Meeting Proceedings of Chinese Society Electrical Engineering:Vol. 2019. Wuhan:State Grid Electric Power Research Institute, 2019:224-228.
• [8] AGüERO A, SPIRADEK K, H?FINGER S, et al.Microstructural evolution of slurry Fe aluminide coating during high temperature steam oxide[C]//Materials Science Forum. 7th Internatioanal Symposium on High Temperature Corrosion and Protection of Materials. Les Embiez:Trans Tech Publications Ltd, 2008, 595:251-259.
• [9]周永莉,鲁金涛,党莹樱,等.低温渗铝涂层对P92钢650℃饱和蒸汽氧化行为的影响[J].动力工程学报,2019, 39(9):770-776.ZHOU Yongli, LU Jintao, DANG Yingying, et al. Effect of low-temperature aluminized coating on oxidation behavior of P92 steel in saturated steam at 650℃[J].Journal of Chinese Society of Power Engineering, 2019,39(9):770-776.
• [10]罗新民,许勇,陈康敏. 1Cr18Ni9Ti不锈钢渗铝层结构及其抗氧化性能[J].金属热处理, 2008, 33(12):42-45.LUO Xinmin, XU Yong, CHEN Kangmin. Microstructure and oxidation resistance of diffusion-treated aluminizing layer on 1Cr18Ni9Ti stainless steel[J]. Heat Treatment of Metals, 2008, 33(12):42-45.
• [11]董猛,谢逍原,朱阳存,等. G115和T92钢表面FeAl渗层制备及其抗高温水蒸汽氧化性能[J].材料热处理学报, 2021, 42(5):135-142.DONG Meng, XIE Xiaoyuan, ZHU Yangcun, et al.Preparation of FeAl penetration layer on G115 and T92steel surface and its oxidation resistance to high temperature steam[J]. Transactions of Materials and Heat Treatment, 2021, 42(5):135-142.
• [12] LU J, DANG Y, HUANG J, et al. Preparation and characterization of slurry aluminide coating on Super304H boiler tube in combination with heat-treatment process[J]. Surface and Coatings Technology, 2019, 370:97-105.
• [13]鲁金涛,党莹樱,黄锦阳,等.火电机组过/再热器锅炉管内壁铝化物涂层研究(Ⅱ):蒸汽氧化、强度及组织演化[J].表面技术, 2020, 49(11):269-276.LU Jintao, DANG Yingying, HUANG Jinyang, et al.Aluminide coating on inner wall of boiler tubes for overheater/reheater of thermal power generating unit(II):steam oxidation, strength and microstructure evolution[J].Surface Technology, 2020, 49(11):269-276.
• [14] GALETZ M C, OSKAY C, MADLOCH S. Microstructural degradation and interdiffusion behavior of NiAl and Ge-modified NiAl coatings deposited on Alloy 602 CA[J].Surface and Coatings Technology, 2019, 364:211-217.
• [15] SMIALEK J L, LOWELL C E. Effects of diffusion on aluminum depletion and degradation of NiAl coatings[J].Journal of the Electrochemical Society, 1974, 121(6):800.
• [16] LATIEF F H, KAKEHI K. Influence of heat treatment on anisotropic creep behavior of aluminide coating on a Nibase single crystal superalloy[J]. Materials&Design,2013, 52:134-142.
• [17] ALAM M Z, SATYANARAYANA D V V, CHATTERJEE D, et al. Effect of prior cyclic oxidation on the creep behavior of bare and Pt-Aluminide coated directionally solidified CM-247LC Alloy[J]. Procedia Engineering,2013, 55:835-841.
• [18] VEYS J M, MEVREL R. Influence of protective coatings on the mechanical properties of CMSX-2 and Cotac784[J]. Materials Science and Engineering, 1987, 88:253-260.
• [19] LI W, CHEN H, LI C, et al. Microstructure and tensile properties of AISI 321 stainless steel with aluminizing and annealing treatment[J]. Materials&Design, 2021, 205:109729.
• [20] BATES B L, ZHANG Y, DRYEPONDT S, et al. Creep behavior of pack cementation aluminide coatings on Grade 91 ferritic-martensitic alloy[J]. Surface and Coatings Technology, 2014, 240:32-39.
• [21] HOU X, ZHANG H, SERAFFON M, et al. Steam oxidation and mechanical performance of a ferritic–martensitic steel with slurry aluminide coating[J].Materials and Corrosion, 2020, 71(8):1310-1320.
• [22] AGüERO A, GONZáLEZ V, GUTIéRREZ M, et al.Comparison between field and laboratory steam oxidation testing on aluminide coatings on P92[J]. Materials and Corrosion, 2011, 62(6):561-568.
• [23] AGüERO A, MUELAS R, GUTIéRREZ M, et al. Cyclic oxidation and mechanical behaviour of slurry aluminide coatings for steam turbine components[J]. Surface and Coatings Technology, 2007, 201(14):6253-6260.
• [24]高海燕,贺跃辉,沈培智. FeAl金属间化合物研究现状[J].材料导报, 2008(7):68-71.GAO Haiyan, HE Yuehui, SHEN Peizhi. Research status of FeAl intermetallics compound[J]. Materials Review,2008(7):68-71.
• [25] BOULESTEIX C, GRéGOIRE B, PEDRAZA F.Oxidation performance of repaired aluminide coatings on austenitic steel substrates[J]. Surface and Coatings Technology, 2017, 326:224-237.
• [26] BOULESTEIX C, PEDRAZA F, PROY M, et al. Steam oxidation resistance of slurry aluminum and aluminum/silicon coatings on steel for ultrasupercritical steam turbines[J]. Oxidation of Metals, 2017, 87(3/4):469-479.
• [27] BOULESTEIX C, KOLARIK V, PEDRAZA F. Steam oxidation of aluminide coatings under high pressure and for long exposures[J]. Corrosion Science, 2018, 144:328-338.
• [28] SUNDAR R S, DEEVI S C. High-temperature strength and creep resistance of FeAl[J]. Materials Science and Engineering:A, 2003, 357(1/2):124-133.
• [29]周瑾,白亚平,成超,等. B2结构FeAl金属间化合物研究现状[J].铸造技术, 2019, 40(8):858-861.ZHOU Jin, BAI Yaping, CHENG Chao, et al. Research status of FeAl intermetallic compounds with B2structure[J]. Foundry Technology, 2019, 40(8):858-861.
• [30] PELLEG J. Fracture in B2 intermetallics, basic compoundsfor superalloys mechanical properties[M].Amsterdam:Elsevier, 2018:517-551.
• [31]李明升,冯长杰,王福会.施加氮化钛铝涂层对1Cr11Ni2W2MoV不锈钢力学性能的影响[C]//中国功能材料及其应用学术会议.第六届中国功能材料及其应用学术会议论文集.重庆:重庆材料研究院，2007,10:178-181.LI Mingsheng, FENG Changjie, WANG Fuhui. Effect of titanium aluminum nitride coating on mechanical properties of 1Cr11Ni2W2MoV stainless steel[C]//China National Conference on Functional Materials and Applications. Proceedings of the 6th China National Conference on Functional Materials and Applications:.Chongqing:Chongqing Institute of Materials Science,2007, 10:178-181.
• [32] F?HSING D, RUDOLPHI M, KONRAD L, et al. Fireside corrosion of chromiumand aluminum coated ferritic–martensitic steels[J]. Oxidation of Metals, 2016, 88(1/2):155-164.
• [33] XIANG Z D, ZENG D, ZHU C Y, et al. Steam oxidation resistance of Ni-aluminide/Fe-aluminide duplex coatings formed on creep resistant ferritic steels by low temperature pack cementation process[J]. Corrosion Science, 2011, 53(1):496-502.
• [34]张德丰,陆建生,宋鹏,等.铂改性铝化物涂层的热生长层内应力研究[J].稀有金属材料与工程, 2011,40(11):1956-1960.ZHANG Defeng, LU Jiansheng, SONG Peng, et al. TGO stress growth for Pt-modified aluminide bond coats during high temperature oxidation[J]. Rare Metal Materials and Engineering, 2011, 40(11):1956-1960.
• [35] TEXIER D, MONCEAU D, HERVIER Z, et al. Effect of interdiffusion on mechanical and thermal expansion properties at high temperature of a MCrAlY coated Nibased superalloy[J]. Surface and Coatings Technology,2016, 307:81-90.
• [36] GALIULLIN T, CHYRKIN A, PILLAI R, et al. Effect of alloying elements in Ni-base substrate material on interdiffusion processes in MCrAlY-coated systems[J].Surface and Coatings Technology, 2018, 350:359-368.
• [37] BELLUCCI A, MATERA S, FRY A, et al. The steam oxidation and mechanical performance of a ferriticmartensitic steel coated with slurry and pack cementation aluminide coating[C]//EPRI. International Conference on Corrosion in Power Plants:. San Diego:EPRI, 2015, 1:1-12.
• [38] DRYEPONDT S, ZHANG Y, PINT B A. Creep and corrosion testing of aluminide coatings on ferritic–martensitic substrates[J]. Surface and Coatings Technology, 2006,201(7):3880-3884.
• [39] AGüERO A, MUELAS R. Steam oxidation ofslurryaluminide coatings on ferritic steels for advancedcoal-fired steam power plants[C]//Materials Science Forum. Trans Tech Publications Ltd:.Les Embiez:Instituto Nacional de Técnica Aeroespacial, 2004, 461:957-964.
• [40]刘亚梅. 9%Cr热强钢焊接金属时效微观组织与力学性能研究[D].秦皇岛:燕山大学, 2015:44-54.LIU Yamei. Study on microstructure and mechanical properties of 9%Cr ferrite heat-resistant steel weld metal after aging[D]. Qinhuangdao:Yanshan University, 2015:44-54.
• [41] SUN Y, DONG J, ZHAO P, et al. Formation and phase transformation of aluminide coating prepared by lowtemperature aluminizing process[J]. Surface and Coatings Technology, 2017, 330:234-240.
• [42]黄春林,朱明,鲁金涛,等. T92钢表面铝化物涂层的组织演化[J].中国表面工程, 2022, 35(4):213-222.HUANG Chunlin, ZHU Ming, LU Jintao, et al. Microstructure evolution of aluminide coating on T92 steel[J].China Surface Engineering, 2022, 35(4):213-222.